BULROC DTH Hammer
BR DTH Hammer
DOWN THE HOLE DRILLING HAMMERS
DTH hammer is used for drilling holes through a wide range of rock types, the variety of which continues to extend well beyond the original conception of early blast hole drilling.
Down-the-Hole refers to where the hammer action occurs when compared to drifter hammers, which hammer on top of the drill string. The DTH hammer piston always makes direct contact with the drill bit and there is generally no loss of transmitted energy as the hammer drills deeper, as is the case with drifter (top hammer) rigs.
Roschen offers a wide range of DTH hammers suitable for a variety of drilling operations. Our Down the Hole hammers provide the most versatile and cost effective rock drilling method.
DTH drilling tool is a kind of drilling system which uses compressed air as motivation, makes drilling impact motivation parts down the hole, to control the piston reciprocating motion by the distribution device in the hammer, and then impacts the DTH bit in the front of the hammer to transit the impacting power to the bit. The DTH bit in the front of the hammer breaks the rock to drill hole.
At present, DTH drilling tool is widely used in underground mining, quarries, hydraulic and Hydro-Power Engineering, water well drilling, Mineral exploration, anchoring hole drilling, geothermal engineering, Subway excavation, another civil engineering. it has the advantage of high flatness, smooth hole wall, high rigid of drill rod and hammer, independent of high axial thrust, no limit of drilling depth, low cost of devices and easiness to maintain. At the drilling hole of diameter 105 mm to diameter 254 mm, a plenty of the DTH drilling tools are used.
The Roschen range of ROS down the hole hammers are strong and robust tools of a simple and straight forward design to provide maximum performance, with a minimum of maintenance.
Please Note:
That, contrary to other ROSCHEN hammer models, the ROS series do use bits with Footvalves.
ROSCHEN ROS hammers are supplied as standard with a Check Valve arrangement which is designed to maintain the pressure inside the hammer when the air is switched off and so help prevent contaminated
water from entering the hammer.
ROSCHEN ROS hammers are designed to give optimum performance with the minimum consumption of compressed air. If, however, particular deep-hole application require extra air flushing. This can be
achieved by drilling through the soft alloy plug in the piston.
Advantages:
1. Valveless air distribution. More reliable.
2. Simple design of the piston. Long life.
3. More efficient energy transfer, fact drilling speed, lower air consumption and lower oil consumption.
4. Fewer internal parts, simple structure, long life, less failure and easier to maintain because all the parts are heat treated.
5. Easy to disassemble because the top sub, the drive chuck and the external cylinder are connected by multi-step thread.
ROSCHEN DTH Hammers Specifications | |||||||
Hammer Size |
Bit Shank |
ROSCHEN Code |
Connection Thread |
Suitable bit |
Working pressure |
Air consumption |
|
2" |
BR2 |
ROS 11 ROS 22 |
RD50 box |
¢70-¢90mm |
0.7-1.75Mpa |
0.7Mpa |
4.5m3/min |
1.0Mpa |
4m3/min |
||||||
1.4Mpa |
5m3/min |
||||||
3" |
DHD3.5 |
ROS 32 |
API 2 3/8" Reg |
¢90-¢110mm |
1.0-1.5Mpa |
1.0Mpa |
4.5m3/min |
COP32/COP34 | |||||||
M30 |
1.5Mpa |
9m3/min |
|||||
4" |
DHD340 |
ROS 34 |
API 2 3/8" Reg |
¢110-¢135mm |
1.0-2.5Mpa |
1.0Mpa |
6m3/min |
COP44 | |||||||
QL40 | |||||||
SD4 |
1.8Mpa |
10m3/min |
|||||
M40 |
2.4Mpa |
15m3/min |
|||||
5" |
DHD350 |
ROS 52 ROS 54 |
API 2 3/8"Reg/API 3 1/2" Reg |
¢135-¢155mm |
1.0-2.5Mpa |
1.0Mpa |
9m3/min |
COP54 | |||||||
QL50 | |||||||
SD5 |
1.8Mpa |
15m3/min |
|||||
M50 |
2.4Mpa |
23m3/min |
|||||
6" |
DHD360 |
ROS 62 ROS 64 |
API 3 1/2" Reg |
¢155-¢190mm |
1.0-2.5Mpa |
1.0Mpa |
10m3/min |
COP64 | |||||||
QL60 | |||||||
SD6 |
1.8Mpa |
20m3/min |
|||||
M60 |
2.4Mpa |
28.5m3/min |
|||||
8" |
DHD380 |
ROS 82 ROS 84 |
API 4 1/2" Reg |
¢195-¢254mm |
1.0-2.5Mpa |
1.0Mpa |
15m3/min |
COP84 | |||||||
QL80 |
1.8Mpa |
26m3/min |
|||||
SD8 |
2.4Mpa |
34m3/min |
|||||
10" |
SD10 |
ROS 100 |
API 6 5/8" Reg |
¢254-¢311mm |
1.0-2.5Mpa |
1.0Mpa |
22m3/min |
Numa100 |
1.8Mpa |
40m3/min |
|||||
ROS 100 |
2.4Mpa |
55m3/min |
|||||
12" |
DHD1120 |
ROS 120 |
API 6 5/8" Reg |
¢305-¢445mm |
1.0-2.5Mpa |
1.0Mpa |
30m3/min |
SD12 |
1.8Mpa |
56m3/min |
|||||
Numa120 |
2.4Mpa |
78m3/min |
|||||
Notes: Metzke, Remet thread is available! |
FAQ
1. Methods of Payment:
T/T (Telegraphic Transfer) or Western Union or L/C at sight
2. Handling time for an order
Only 2 or 3 days if we have stock on your request size.
Based on order quantity, normally it takes 25 days for production.
3. Shipping way
Sample order: we suggest Courier express like DHL/UPS/TNT/FEDEX or by air
Bulk order: we suggest by air or by sea.
4. Quality Control
We have our own experienced QC.
There will be strict inspection and testing for every order before shipping out.
5. After Services:
(1). Our sales team will response for your question within 24 hours (Holidays Excluded)
(2). Technical Support will be available in any time
(3). Free replacement will provide once the failure confirmed caused by our product quality
6.How can we trust your company?
We support Alibaba trade insurance. Protecting products quality, shipment on time and your covered amount.
Any other questions,please feel free to contact with me online or by phone.